View S5F333SZ03-LBB0_1304001.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

1/3 INCH CCD IMAGE SENSOR FOR VGA COMPATIBILITY
S5F333SZ03
INTRODUCTION
The S5F333SZ03 is an interline transfer progressive scan type square pixel CCD area image sensor of 1/3 inch optical format developed for VGA. The electron accumulation time can be changed by the electronic shutter function and it is possible to obtain a frame still image without a mechanical shutter. High resolution and good color reproduction are accomplished by using mosaic R, G, B primary color filters. It is suitable for still cameras and PC input cameras.
16Pin Cer - DIP
FEATURES
* * * * * * * * * * * 330K Pixel Progressive-scan CCD High Vertical Resolution (480 TV lines) Square Unit Pixel for VGA Format No Substrate Voltage Adjustment No DC bias on Reset Clock R, G, B Mosaic On-Chip Color Filter Optical Size 1/3 inch Format Variable Speed Electronic Shutter Low Smear High Antiblooming Horizontal Register 5V Drive
ORDERING INFORMATION
Device S5F333SZ03-LBB0 Package 16Pin Cer - DIP Operating -10 C - +60 C
STRUCTURE
* * * * * Number of Total Pixels: Number of Effective Pixels: Chip Size: Unit Pixel Size: Optical Blacks & Dummies: 692(H) x 504(V) 659(H) x 494(V) 6.00mm(H) x 4.95mm(V) 7.40 m(H) x 7.40 m(V) Refer to Figure Below
16 2
659
31 2 Dummy Pixels
Effective Imaging Area (Top view)
OUTPUT
V-CCD
494 8 5
Optical Black Pixels
Effective Pixels
H-CCD
1
S5F333SZ03
1/3 INCH CCD IMAGE SENSOR FOR VGA COMPATIBILITY
BLOCK DIAGRAM
(Top View)
8 VOUT
7 GND
6 NC
5 GND
4 NC
V1
3
V2
2
V3
1
Vertical Shift Register CCD
Vertical Shift Register CCD
Vertical Shift Register CCD
Vertical Shift Register CCD
G R G G R G R
B G B B G B G
G R G G R G R
B G B B G B G
Horizontal Shift Register CCD
to substrate
9 VDD
10 NC
11 GND
SUB
12
13 VL
RS
14
H1
15
H2
16
Figure 1. Block Diagram
PIN DESCRIPTION
Table 1. Pin Description Pin 1 2 3 4 5 6 7 8 Symbol V3 V2 V1 NC GND NC GND VOUT Description Vertical CCD transfer clock 3 Vertical CCD transfer clock 2 Vertical CCD transfer clock 1 No connection Ground No connection Ground Signal output Pin 9 10 11 12 13 14 15 16 Symbol VDD NC GND SUB VL RS H1 H2 Description Output stage drain bias No connection Ground Substrate clock Protection circuit bias Reset gate clock Horizontal CCD transfer Horizontal CCD transfer
2
1/3 INCH CCD IMAGE SENSOR FOR VGA COMPATIBILITY
S5F333SZ03
ABSOLUTE MAXIMUM RATINGS (1)
Table 2. Absolute Maximum Ratings Characteristics Substrate clock voltage Symbols SUB - GND SUB - VDD SUB - VOUT Supply voltage Vertical clock input voltage VDD, VOUT - GND V1 - VL V2, V3 - VL V1 - SUB V2, V3 - SUB Horizontal clock input voltage H1, H2 - GND H1, H2 - VL H1, H2 - SUB Output clock input voltage RS - VL RS - SUB RS - GND Protection circuit bias voltage SUB - VL GND - VL Operating temperature Storage temperature TOP TSTG Min. -0.3 -0.3 -0.3 -0.3 -0.3 -0.3 -40 -40 -0.3 -0.3 -40 -0.3 -40 -0.3 -16 -0.3 -10 -30 Max. 40 40 40 17 17 32 17 (2) 32 17 17 substrate DC bias (3) 17 substrate DC bias (2) 17 (2) 40 17 60 80 Unit V V V V V V V V V V V V V V V V C C
NOTE: 1. The device can be destroyed, if the applied voltage or temperature is higher than the absolute maximum rating voltage or temperature. 2. VDD bias must be operated before reset pulse operation. 3. Substrate DC bias(OFD bias) must be operated before horizontal, reset pulse operation.
3
S5F333SZ03
1/3 INCH CCD IMAGE SENSOR FOR VGA COMPATIBILITY
DC CHARACTERISTICS
Table 3. DC Characteristics Item Output stage drain bias Protection circuit bias voltage Substrate clock Output stage drain current Symbol VDD VL SUB IDD Min. 14.55 Typ. 15.0 Max. 15.45 Unit V Remark
The lowest vertical clock level
NOTE
V mA
5.0
NOTE: A DC bias (OFD bias) is generated within the CCD.
CLOCK VOLTAGE CONDITIONS
Table 4. Clock Voltage Conditions Item Read-out clock voltage Vertical transfer clock voltage Symbol VVH2, VVH3 VVM1 ~ V VM3 VVL1 ~ V VL3 Horizontal transfer clock voltage VHH1, VHH2 VHL1, VHL2 Charge reset clock voltage VRSH VRSL Substrate clock voltage VSUB Min. 14.55 -0.05 -8.0 4.75 -0.05 4.75 -0.05 21.5 Typ. 15.0 0.0 -7.5 5.0 0.0 5.0 0.0 22.5 Max. 15.45 0.05 -7.0 5.25 0.05 5.25 0.05 23.5 Unit V V V V V V V V Remark High Middle Low High Low High Low Shutter
4
1/3 INCH CCD IMAGE SENSOR FOR VGA COMPATIBILITY
S5F333SZ03
DRIVE CLOCK WAVEFORM CONDITIONS
Read Out Clock Waveform
100% 90%
VVH2, VVH3
10% 0% tr twh tf 0V
Vertical Transfer Clock Waveform
O V 1
V V HH V VH L V V HL V VH3
V VHH
V VH
V VL 3 V VL L
V VL H V VL
O V 2
V V HH
V V HH
V VH V VH L
O V 3
V VH V VH H
V VHH
V VH2
V VH L
V VHL
V V H4
V V HL
V VL 2
V VL H
V VL H
V VL L V VL VVH = V VH 2
V VL 4
V VL L V VL
V VH H
= V V H + 0. 3V
V V L = (V V L 1 + V V L 3)/ 2 V O V = V V H n - V V L n
(n =1~3 )
V V H L = V V H - 0. 3 V V V L H = V V L + 0. 3V V V L L = V V L - 0. 3 V
5
S5F333SZ03
1/3 INCH CCD IMAGE SENSOR FOR VGA COMPATIBILITY
Horizontal Transfer Clock Waveform Diagram
tr twh tf
90% VOH 10% VHL twl
Reset Gate Clock Waveform Diagram
tr twh tf VRGH twl VORG Point A RG waveform VRGLH VRGLL VRGL + 0.5V VRGL
OH1 waveform 10%
VRGLH is the maximum value and VRGLL is the minimum value of the coupling waveform in the period from Point A in the diagram about to RG rise VRGL = (VRGLH + VRGLL)/2, VFRG = VRGH - VRGL
Substrate Clock Waveform
100% 90%
VOSU B 10% VSUB 0% tr twh tf
6
1/3 INCH CCD IMAGE SENSOR FOR VGA COMPATIBILITY
S5F333SZ03
CLOCK EQUIVALENT CIRCUIT CONSTANT
Table 5. Clock Equivalent Circuit Constant
twh Item Read-out clock Vertical clock Symbol Min. VH V1, V2 V3 H1 Horizontal clock Reset clock Substrate clock H2 RG SUB 24 26.5 11 1.5 30 31.5 13 1.8 25 25 31.5 30 62.5 10 10 3 0.5 17.5 15 2.3 Typ. Max. 2.5 Min. Typ. Max. Min. Typ. 0.5 15 10 10 3 0.5 Max. Min. Typ. 0.5 350 17.5 15 Max. s ns ns ns ns s twl tr tf Unit
7
S5F333SZ03
1/3 INCH CCD IMAGE SENSOR FOR VGA COMPATIBILITY
EQUIVALENT CIRCUIT PARAMETERS
Table 6. Equivalent Circuit Parameters Item Capacitance between vertical transfer clock and GND Symbol CV1 CV2 CV3 Capacitance between vertical transfer clocks CV12 CV23 CV31 Capacitance between horizontal transfer clock and GND Capacitance between horizontal transfer clocks Capacitance between reset gate clock and GND Vertical transfer clock serial resistor CH1, CH2 CH12 CRS RV1, RV2 RV3 Horizontal transfer clock serial resistor Reset gate clock serial resistor Vertical transfer clock ground resistor CH1, CH2 RRS RGND Typ. 1,700 1,700 2,100 2,700 2,100 1,100 117 39 10 30 25 10 100 15 Unit pF pF pF pF pF pF pF pF pF
V1 CV12 CV1 RGND CV31 C V3 CV23 CV2
V2 H1
RH1
CH12 C H1
RH2 H2 CH2
Horizontal Clock Equivalent Circuit
CRG RS CRS
V3
Vertical Clock Equivalent Circuit
Reset Clock Equivalent Circuit
8
1/3 INCH CCD IMAGE SENSOR FOR VGA COMPATIBILITY
S5F333SZ03
OPERATING CHARACTERISTICS
Device Temperature = 25 C Table 7. Operating Characteristics Item G sensitivity Sensitivity ratio Symbol Sg Rr Rb Saturation signal Smear Blooming margin Uniformity Dark signal (NOTE) Dark shading (NOTE) Color uniformity Line stripe W, R, G, B
NOTE: Test Temperature = 60 C
Min. 38 0.3 0.4 550
Typ. 45 0.45 0.55
Max.
Unit mV/Iux
Remark 1 1
0.6 0.7 mV
YSAT SM BM U D D DSGr, DSGb LCG, LCR, LCB
2 3
0.005 1,000
0.015 times 20 2 1 8 3.8 % mV mV % %
4 5 6 7 8 9
TESTING SYSTEM
A
CCD signal output
Gr/Gb S/H Gr/Gb color signal output
CCD
C. D. S
AMP R/B S/H R/B color signal output
Figure 2. Testing System
9
S5F333SZ03
1/3 INCH CCD IMAGE SENSOR FOR VGA COMPATIBILITY
TEST CONDITION
1. Use a light source with color temperature of 3,200K hallogen lamp and CM-500S for IR cut filter. The light source is adjusted in accordance with the average value of Y signals indicated in each item.
COLOR FILTER ARRAY
The color filter array of this image sensor is shown below. This primary mosaic CFA is used with the operation of frame mode, where all of the photosensors are read out sequentially.
Cb R Gb R
B Gr B Gr
Gb R Gb R
B Gr B Gr
CCD
Figure 3. Color Filter Array
10
1/3 INCH CCD IMAGE SENSOR FOR VGA COMPATIBILITY
S5F333SZ03
TEST METHODS
1. Measure the light intensities(L) when the average illuminance output value(Y) of green pixels Gr is equal to the standard illuminance output value of 150mV (YA), and when it is equal to half of 150mV, 1/2 xYA. repeat for Gb. and calculate Sgr, Sgb, and Sg.
Sg r 1 1 Y A - ---Y A Y A - ---Y A 2 2 = ---------------------------- , S gb = ---------------------------- , S g = Sgr + S gb LY - L 1 LY - L 1
A
-- Y A 2
A
---Y A 2
The sensitivities for red and blue pixels, Sr and Sb, are also measured in the same way.
Sb Sr R r = ------, R b = -----Sg Sg
2. Adjust the light intensity to 15 times of the value with which Y is YA, then measure the averaged illuminance output value (Y = YSAT).
3. When the Gr pixel signal value, Ygr is 150mV, measure the Gb, R, B pixel signal values, Ygb, Yr, and Yb respectively. Adjust the light intensity until 500 times of the illumination under which 150 mV of Gr pixels value is obtained, is reached. Remove the read-out clock and drain the signal in photosensors by electronic shutter operation during the horizontal blanking time without changing other clocks. Measure the maximum output value YSM regardless of the pixel type..
Y g r + Y g b + Y r + Yb 1 1 SM = Y SM / --------------------------------------------------- x ---------- x ------ x 100 ( % ) 4 500 10
4. Measure the light intensity(LBM) on which the Y signal output value of the optical black pixels (OBP) is rapidly increased with the increasing light intensity.
L BM BM = ----------LY
A
5. Measure the maximum and minimum illuminance output value (YMAX, YMIN) when the light intensity is adjusted to make Y to be YA.
Y MAX - Y MIN U = ----------------------------------- x 100 ( % ) YA
6. Measure YD with the horizontal idling time transfer level as reference, when the device ambient temperature is 60 C and all of the light sources are shielded.
11
S5F333SZ03
1/3 INCH CCD IMAGE SENSOR FOR VGA COMPATIBILITY
7. Follow test method 6, measure the maximum (DMAX) and minimum illuminance output (DMIN).
D = DMAX - D MIN
8. When the Gr pixel signal value is 150mV, measure the maximum and minimum output pixel values (YMAX(Gr)), YMIN(Gr)), Repeat for Gb, R, B under the each pixel value,150mV
Y MAX ( i ) + Y MIN ( i ) DSi = ----------------------------------------------- x 100 ( % ) Yi
where i = Gr, Gb, R, B
9. Adjust the light intensity to make the each pixel value, 150mV, using red(R), green(G) and blue(B) optical filters respectively and measure the differences (YR, YG, YB) between the signal lines.
Y i Lci = -------------------- x 100 ( % ) 150mV
where i = R, G, B
12
1/3 INCH CCD IMAGE SENSOR FOR VGA COMPATIBILITY
S5F333SZ03
SPECTRAL RESPONSE CHARACTERISTICS
Excluding Light Source Characteristics
1.0 0.9 0.8 Relative Response 0.7 0.6 0.5 0.4 0.3 0.2 0.1 0.0 400 450 500 550 Wavelength (nm) 600 650
Wave Lelength (nm)
Blue Green Red
700
Figure 4. Spectral Response Characteristics
13
S5F333SZ03
1/3 INCH CCD IMAGE SENSOR FOR VGA COMPATIBILITY
APPLICATION CIRCUITS
15V 22 XSUB XV1 XV2 SG XV3 SG
103
+10/10V
H2 H1 RS
1
2
3
4
5
6
7
8
9
10
S5C7221X01
20 19 18 17 16 15 14 13 12 11
102
22
1 2 3 4 5 6
V3 V2 V1 NC GND NC GND VOUT
H2 16 H1 15
S5F333SZ03
RS 14 100 VL 13 SUB 12 GND 11 NC 10 VDD
15V
7
1/35V
8 +
9
0.01 3.3/20V
2200P 0.1 100K 100 C3882 3.9K 1M
103
103
+10/25V 22 -7.5V 22
+10/25V CCD output 15V
Figure 5. Application Circuits
14
+
1/3 INCH CCD IMAGE SENSOR FOR VGA COMPATIBILITY
S5F333SZ03
READ-OUT CLOCK TIMING CHART
1/30 sec noninterlace transfer
Unit: [s]
HD
SG V1
V2
V3
42.4 (520bits) 2.04 (25bits) 2.53 (31bits)
Figure 6. Read-out Clock Timing Chart
15
S5F333SZ03
1/3 INCH CCD IMAGE SENSOR FOR VGA COMPATIBILITY
CLOCK TIMING CHART (VERTICAL SYNC.)
VD
525 1 525 1
14 15
HD
V1 V2 V3 SG CCD out
490 491 492 493 494 490 491 492 493 494 123456781234 123456781234
Figure 7. Clock Timing Chart (Vertical Sync.)
16
14 15
7
7
1/3 INCH CCD IMAGE SENSOR FOR VGA COMPATIBILITY
S5F333SZ03
CLOCK TIMING CHART (HORIZONTAL SYNC.)
36
24
60
1 60
12
1
78
48
36
1
12
24
1
1
1
HD/SYNC
780 1
35
SHD
SHP
1
1
1 SUB V2 V3 H1 H2
CLK
BLK
RG
Figure 8. Clock Timing Chart (Horizontal Sync.)
V1
23
17
S5F333SZ03
1/3 INCH CCD IMAGE SENSOR FOR VGA COMPATIBILITY
PACKAGE DIMENSIONS
Unit: m m t = 0.253/40.02
8.203/40.10 10.003/40.10 11.403/40.10 2.50 2-R0.50
7.203/40.10 9.203/40.10 12.203/40.12
1.103/40.08 2.803/40.30 1.273/40.25 3.503/40.50
0.303/40.10 1.273/40.05 1.277 = 8.893/40.10 11.603/40.12
Figure 9. Package Dimensions
18
1/3 INCH CCD IMAGE SENSOR FOR VGA COMPATIBILITY
S5F333SZ03
HANDLING INSTRUCTIONS
* Static Charge Prevention CCD image sensors can be easily damaged by static discharge. Before handling, be sure to take the following protective measures. -- Use non chargeable gloves, clothes or material. Also use conductive shoes. -- When handling directly, use an earth band. -- Install a conductive mat on the floor or working table to prevent generation of static electricity. -- Ionized air is recommended for discharging when handling CCD image sensor. -- For the shipment of mounted substrates, use boxes treated for the prevention of static charges.
*
Soldering -- Make sure the package temperature does not exceed 80 C. -- Solder dipping in a mounting furnace causes damage to the glass and other defects. Use a grounded 30W soldering iron and solder each pin in less than 2 seconds. For repairs and remount, cool sufficiently. -- To dismount an imaging device, do not use a solder suction equipment. When using an electronic disoldering tool, use a thermal controller of the zero cross on/off type and connect to ground.
*
Dust and Dirt Protection -- Operate in the clean environments (around class 1000 will be appropriate). -- Do not either touch glass plates by hand or have object come in contact with glass surface. Should dirt stick to a glass surface blow it off with an air blow (for dirt stuck through static electricity ionized air is recommended). -- Clean with a cotton bud and ethyl alcohol if the glass surface is grease stained. Be careful not to scratch the glass. -- Keep in case to protect from dust and dirt. To prevent dew condensation, preheat or precool when moving to a room with great temperature differences. -- When a protective tape is applied before shipping, just before use remove the tape applied electrostatic protection. Do not reuse the tape.
*
Do not expose to strong light (sun rays) for long period, color filter are discolored.
*
Exposure to high temperature or humidity will affect the characteristics. accordingly avoid storage or usage in such conditions.
*
CCD image sensors are precise optical equipment that should not be subject to mechanical shocks.
19

▲Up To Search▲

Price & Availability of S5F333SZ03-LBB0

	To Download S5F333SZ03-LBB0 Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .